How To Install a Shower Pan in Singapore? Expert Guide!

If the water doesn’t go to the drain and keeps falling on the shower floor, it can damage the floor and also cause leaks. Thanks to the shower pan that directs the water directly toward the drain, so that it doesn’t cause any damage to the floor. However, how to install a shower pan in Singapore?

It’s quite easy to do. All you have to do is read this post all the way through to the end so you may not miss something crucial. Everything will be explained step by step. LS Plumber Singapore also offers clear bathtub choke, drain choke repair, and storage water heater services in Singapore.

Benefits Of Installing A Shower Pan In Singapore

There are many advantages of installing a shower pan in Singapore, and these include:

• It stops water from leaking onto your bathroom floor.
• Helps keep mold and damp problems away.
• It makes the water flowing directly to the rain instead of damaging the floor
• It prevents the leaks and also the floor damage that could cost you a lot
• It gives you a stable and solid surface to stand on and take a shower safely
• Quicker and simpler to install than tiling the floor.
• Fits well in smaller HDB or condo bathrooms.
• Lowers the risk of cracks or water seeping through.
• Makes your shower area look clean and complete.

How to Install a Shower Pan in Singapore?

Installing a shower pan is actually easy, and you can do it yourself. You only need to follow these steps shared by our experts.

Check And Prepare The Floor

Before anything else, make sure the floor is clean and solid. Sweep away dirt, old glue, or leftover chunks from past work. If you spot cracks or holes, patch them up and wait for them to dry. The floor also has to be level. 

If it’s not, spread some floor leveler on and smooth it out. Getting this right means your shower pan won’t rock or shift later.

Measure The Area For The Shower Pan

Grab your tape measure and check the length and width of the spot where the pan will go. Write the numbers down so you don’t forget.

Double-check because if your measurements are off, nothing else will fit right. Also, check where the drain pipe is. You want to be sure the pan’s drain will line up with it before you move on.

Place The Shower Pan And Check The Fit

Set the pan down gently where you want it. It should sit flat with no wobbling or rocking. Give it a little press and make sure it feels steady. 

Look at the drain hole and check that it lines up with the pipe under the floor. If something feels off, stop and figure it out now. It’s a lot easier to fix before you go any further.

Mark The Drain Hole And Remove The Pan

Once you’ve got the pan sitting right, grab a pencil or marker and trace around the drain hole onto the floor. Make the marks clear because you’ll need them later. 

After you’re done marking, lift the pan out and set it aside carefully. This step saves you a lot of guessing when it’s time to install the drain fitting. You want to get it right on the first try.

Apply The Mortar Mix On The Floor

Mix up your mortar the way it says on the bag. Don’t just eyeball it. Once it’s ready, spread it out on the spot where the pan will sit. Use a trowel and aim for an even layer, not too thick, not too thin. 

The mortar helps lock the pan in place and stops it from shifting around later. Work quickly because mortar doesn’t wait around for anyone.

Set The Shower Pan Into Place

Pick up the pan and lower it gently onto the mortar. Press down a bit with your hands so it settles in nicely. Give it a slight wiggle to help it sink into the mortar evenly. 

Double-check that the drain hole still lines up with the pipe below. Once it feels snug and level, leave it alone so the mortar can set. Don’t stand on it or mess with it while it’s drying.

Attach The Drain Fitting To The Pan

Now it’s time to put the drain pieces together. Start by fitting the rubber gasket and the drain ring into place. Tighten them up by hand first. 

If you need a bit more grip, you can use a wrench, but go easy. The goal is to make sure the drain seals tight so water won’t leak out. Take your time here because fixing a leak later is a hassle.

Seal The Edges With Silicone Caulk

Get a good waterproof silicone caulk made for bathrooms. Run a line along the edge where the pan meets the walls and the floor. Smooth it out with your finger or a tool to make sure there are no gaps. 

This seal keeps water from sneaking under the pan. Don’t rush it, and let the caulk dry all the way before you start using the shower.

Let Everything Dry And Test The Shower Pan

Wait for both the mortar and caulk to dry fully. Check the instructions on both products for how long that takes. When it’s dry, pour a bit of water into the pan and see how it drains. 

Look around the edges and the drain for any leaks. If everything’s dry and the water flows out right, you’re good to go. Your shower pan is set.

Final Words

Installing a shower pan can protect your floor from damage and also prevent water leaks in the shower. How to install a shower pan in Singapore?

These are the steps to follow: First, clean and level the floor, then measure the area and check the drain position. Place the shower pan to test the fit, then mark the drain hole and remove the pan. 

Mix and spread mortar on the floor, then set the pan firmly into place. Attach the drain fitting securely, then seal the edges with bathroom silicone. 

Let everything dry completely, then test the pan with water and check for leaks. Follow each step carefully to avoid mistakes.

Frequently Asked Questions